- 您现在的位置：买卖IC网 > Sheet目录874 > Q48T30015-NBB0 (Power-One)CONV DC-DC 48V IN 1.5V OUT 45W
Q48T30015 DC-DC Converter Data Sheet
36-75 VDC Input; 1.5 VDC @ 30A Output
Q Family
When using remote sense, the output voltage at the con-
verter can be increased by as much as 10% above the
nominal rating in order to maintain the required voltage
across the load. Therefore, the designer must, if necessary,
decrease the maximum current (originally obtained from the
derating curves) by the same percentage to ensure the con-
Vin
Vin (+)
ON/OFF
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
R T-INCR
Rload
verter’s actual output power remains at or below the maxi-
mum allowable output power.
Vin (-)
Vout (-)
Output Voltage Adjust /TRIM (Pin 6)
The converter’s output voltage can be adjusted up 10% or
down 20% relative to the rated output voltage by the addition
of an externally connected resistor.
The TRIM pin should be left open if trimming is not being
used. To minimize noise pickup, a 0.1 μ F capacitor is con-
nected internally between the TRIM and SENSE(-) pins.
To increase the output voltage, refer to Fig. 4. A trim resistor,
Fig. 4: Configuration for increasing output voltage .
R T ? DECR = Required value of trim-down resistor [k ? ]
and ? is as defined above.
Note: The above equations for calculation of trim resistor
values match those typically used in conventional industry-
standard quarter bricks.
Q Family
R T-INCR , should be connected between the TRIM (Pin 6) and
SENSE(+) (Pin 7), with a value of:
Vin (+)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
R T ? INCR =
5.11(100 + ? )V O ? NOM ? 626
1.225 ?
? 10.22 [k ? ]
Vin
ON/OFF
Vin (-)
TRIM
SENSE (-)
Vout (-)
R T-DECR
Rload
where,
R T ? INCR = Required value of trim-up resistor k ? ]
V O ? NOM = Nominal value of output voltage [V]
Fig. 5: Configuration for decreasing output voltage.
? =
(V O - REQ ? V O - NOM )
V O - NOM
X 100 [%]
Trimming/sensing beyond 110% of the rated output voltage
is not an acceptable design practice, as this condition could
cause unwanted triggering of the output over-voltage protec-
tion (OVP) circuit. The designer should ensure that the dif-
V O ? REQ = Desired (trimmed) output voltage [V].
When trimming up, care must be taken not to exceed the
converter‘s maximum allowable output power. See previous
section for a complete discussion of this requirement.
To decrease the output voltage (Fig. 5), a trim resistor,
R T-DECR , should be connected between the TRIM (Pin 6) and
SENSE(-) (Pin 5), with a value of:
ference between the voltages across the converter’s output
pins and its sense pins does not exceed 0.15 V, or:
[V OUT ( + ) ? V OUT ( ? )] ? [V SENSE ( + ) ? V SENSE ( ? )] ≤ 0.15 [V]
This equation is applicable for any condition of output sens-
ing and/or output trim.
R T ? DECR =
where,
511
?
? 10.22 [k ? ]
MAY 02, 2003 revised to NOV 20, 2006
Page 6 of 14
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
Q48T30018-NBA0
DC/DC QTR BRICK 54W 1.8V T/H
Q48T30025-NDB0
DC/DC QTR BRICK 75W 2.5V T/H
Q48T30033-NAAC
DC/DC QTR BRICK 100W 3.3V T/H
QAK2J335KTP
CAP FILM 3.3UF 630VDC AXIAL
QD48S018033-NS00
DC/DC QTR BRICK 77W 1.8/3.3V
QD48T012025-NCB0
DC/DC QTR BRICK DL 1.2/2.5V T/H
QD48T018025-NBB0
CONV DC-DC 37.5W 2.5/1.8V DUAL
QD48T025033-NBB0
CONV DC-DC 48V IN 3.3/2.5V DUAL
相关代理商/技术参数
Q48T30015-NBBP
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 30V 1.5A - Bulk
Q48T30015-NBBPG
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 30V 1.5A - Bulk
Q48T30015-NBC0
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1.5V 30A - Bulk
Q48T30015-NBC0G
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1.5V 30A - Bulk
Q48T30015-NBCP
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 30V 1.5A - Bulk
Q48T30015-NBCPG
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 30V 1.5A - Bulk
Q48T30015-NCA0
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1.5V 30A - Bulk
Q48T30015-NCA0G
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1.5V 30A - Bulk